Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
The content which follows involving Installing A Bathtub is highly entertaining. You should see for yourself.
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the job can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make sure you have certified yourself for the work and fit trying it. Instead of working with a contractor to take control of a halfway-completed task, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have already acquired a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product list ought to make up the following:
Getting ready for the Installment
Firstly, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub up until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the maker provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that content about How to Install a Bathtub Yourself while doing a search on the internet. Sharing is good. You won't know, you may be helping someone out. Thank you for your time. Visit us again soon.
Get Quote Report this page